CraftZone Malaysia - Malaysian Crafter Blogs

Wednesday, March 13, 2013

Glue E-6000

Assalamualaikum,

Superb glue ever~!
Disini saya nak memperkenalkan gam E-6000 yang superb gila! Sebagai crafter, gam antara barang yang PERLU ada dalam simpanan. Bermacam-macam gam yang saya pernah cuba dan pakai sebab barang clay tak boleh sewenangnya pakai gam biasa. 'Glue Gun' pun tak lepas. Gerenti! So here it is gam yang kuat and mostly crafter dari oversea menggunakan gam ini. 

Price: RM35 
"DIJAMIN BERKESAN"
Ini details berkenaan gam E-6000 ini (copy paste from Michael Website)                            

E-6000® comes in a 3.7 oz tube or carded 2.0 oz tube with applicator nozzle that contains thick, permanent bonding adhesive. It’s a tough, flexible and highly versatile rubber based compound that exhibits exceptional adhesive, contact adhesive and sealant qualities. It’s washer and dryer safe.
COMMONLY USED SURFACE-TO-SURFACE APPLICATIONS ARE:
  • Glass / Rhinestone
  • Clay Pottery / Rocks / Sea Shells
  • Beads / Fabric
  • Ceramic / Wood
  • Glass / Metal
DIRECTIONS  & TIPS FOR USING E-6000®:
  1. Apply E-6000® directly to each surface to be bonded.
  2. Allow E-6000® to partially cure 10 minutes before bringing surfaces together.
Note: E-6000® hardens by solvent evaporation and forms an immediate bond that is difficult to reposition after both adhesive coated surfaces are placed in contact with each other and sufficient pressure is exerted to establish full contact.
SPECIAL TIPS:  To extend life of product, be sure cap is secured back to original position.  Use a toothpick as a disposable applicator for very small applications such as beading.  Remove, recap and allow plastic nozzle to dry. Remove dried product from nozzle by pulling out through threaded end and reuse nozzle.
TEMPERATURE RECOMMENDATIONS/LIMITATIONS:  Performs best when applied at 70 to 85 degrees F. When fully cured, product can withstand temperatures between -40 and 150 degrees F.
GAP FILLING ABILITY:  Up to ¼-inch
CLEAN UP & REMOVAL RECOMMENDATIONS:  Uncured E-6000® can be cleaned by using small amounts of solvents such as Acetone, Tolulene or Naphtha. Cured E-6000® requires scraping or cutting away product with sharp knife and use of mineral spirits (i.e. gasoline, lighter fluid, lacquer thinner) to soften product.
CAUTION ADVISORIES OR SAFETY RECOMMENDATIONS:  Use E-6000® in a well ventilated area.  E-6000® may damage finished surfaces.  Avoid prolonged contact until E-6000® is completely dry.  Do not dry clean.  Always test material samples prior to use on an original project where reversibility is important

                                                     
Sangat bagus bagi crafter yang menggunakan polymer clay. :)

11 comments:

Fairus Basir from The Juggling Queen said...

u jual ke ?

N'Craft said...

yup :) tapi pre-order

Aaron said...

hello ~ do you still sell this e6000 glue ? can i buy ?

Anonymous said...

i nak bwli boleh?
dun

Unknown said...

hi.. d0 u still sell diz glue.. i wan t0 buy diz...

LuLu Evangelyssta said...

Hello there... is this glue still available for pre-order? Pls let me know soonest. Thanks!

LuLu Evangelyssta said...

Hello there... is this glue still available for pre-order? Pls let me know soonest. Thanks!

Adventures said...

Hello is this glue still available? Where can I order or find this glue in stores? Thanks

einafrogies said...
This comment has been removed by the author.
einafrogies said...

Ada lg x dear

Unknown said...

Hi..masih jual ke?